Linux start screenshot

Screenshot showing the serial text console during boot (on APF9328)

U-Boot 1.3.4 (Mar  7 2009 - 18:03:27) apf9328 patch 3.8

I2C:   ready
DRAM:  16 MB
Flash:  8 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
## Booting kernel from Legacy Image at 100a0000 ...
   Image Name:   Linux-2.6.27.13
   Created:      2009-03-07  17:09:47 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1604764 Bytes =  1.5 MB
   Load Address: 08008000
   Entry Point:  08008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.......................................................................................................... done, booting the kernel.
Linux version 2.6.27.13 (eric@shuttle) (gcc version 4.2.1) #1 PREEMPT Sat Mar 7 18:09:45 CET 2009
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: Armadeus APF9328
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: console=ttySMX0,115200n8 mtdparts=physmap-flash.0:256k(U-boot)ro,128k(U-boot_env),256k(firmware),2048k(kernel),-(root) root=/dev/mtdblock4 rootfstype=jffs2 ip=192.168.000.10:192.168.000.2:192.168.000.1:255.255.255.0:apf9328::off
PID hash table entries: 64 (order: 6, 256 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 16MB = 16MB total
Memory: 12808KB available (3052K code, 220K data, 116K init)
Calibrating delay loop... 95.84 BogoMIPS (lpj=479232)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 440 bytes
NET: Registered protocol family 16
--- Registering APF9328 ressources
--- APF9328 ressources registered
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
i.MX Framebuffer driver
Console: switching to colour frame buffer device 60x34
Serial: IMX driver
imx-uart.0: ttySMX0 at MMIO 0x206000 (irq = 30) is a IMX
console [ttySMX0] enabled
imx-uart.1: ttySMX1 at MMIO 0x207000 (irq = 24) is a IMX
brd: module loaded
dm9000 Ethernet Driver, V1.31
eth0: dm9000e at c1854000,c1856002 IRQ 110 MAC: 00:1e:ac:00:00:02 (eeprom)
Driver 'sd' needs updating - please use bus_type methods
physmap platform flash device: 02000000 at 10000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
5 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 5 MTD partitions on "physmap-flash.0":
0x00000000-0x00040000 : "U-boot"
0x00040000-0x00060000 : "U-boot_env"
0x00060000-0x000a0000 : "firmware"
0x000a0000-0x002a0000 : "kernel"
0x002a0000-0x00800000 : "root"
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
usb: imx_udc version: 0.5
USB clock 48000000Hz detected
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i.MX mmc driver
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hal_imx: pid 8210, vid 8210

hal_imx: controller address c0325258

hal_imx: isp1761_register_driver(drv=c0337870)

isp1761 isp1761.0: NXP ISP1761
isp1761 isp1761.0: new USB bus registered, assigned bus number 1
isp1761 isp1761.0: irq 138, io mem 0x00000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
drivers/armadeus/isp1761/hal/hal_imx.c: Registered Driver ISP1761HCD
pehci: Host Driver has been Registered
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
usb 1-1: new high speed USB device using isp1761 and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
imx-mmc imx-mmc.0: card removed
IP-Config: Complete:
     device=eth0, addr=192.168.0.10, mask=255.255.255.0, gw=192.168.0.1,
     host=apf9328, domain=, nis-domain=(none),
     bootserver=192.168.0.2, rootserver=192.168.0.2, rootpath=
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 116K
init started: BusyBox v1.12.1 (2009-03-07 17:57:33 CET)
starting pid 259, tty '': '/sbin/mdev -s'
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
starting pid 271, tty '': '/etc/init.d/rcS'
Starting portmap: done
Initializing random number generator... done.
Starting network...
ip: RTNETLINK answers: File exists
Mounting all filesystems in /etc/fstab
starting pid 303, tty '/dev/ttySMX0': '/sbin/getty -L ttySMX0 115200,57600,38400 vt100'



Welcome to the Armadeus development environment.
armadeus login: root
#