GTKTerm - Revision history

FabienM at 08:01, 28 September 2015

2015-09-28T08:01:01Z

← Older revision		Revision as of 10:01, 28 September 2015
Line 1:		Line 1:
			[[Category: terminal]]

	GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the Serial line. With it you can have access to the U-Boot/Linux console of your APF without needing to connect a keyboard/screen to the board. ([http://tldp.org/HOWTO/Remote-Serial-Console-HOWTO/ For more informations on remote console])		GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the Serial line. With it you can have access to the U-Boot/Linux console of your APF without needing to connect a keyboard/screen to the board. ([http://tldp.org/HOWTO/Remote-Serial-Console-HOWTO/ For more informations on remote console])

JulienB at 09:49, 5 May 2011

2011-05-05T09:49:40Z

← Older revision		Revision as of 11:49, 5 May 2011
Line 1:		Line 1:
	GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the ~~RS232~~ line. With it you can have access to the U-Boot/Linux console of your APF without needing to connect a keyboard/screen to the board. ([http://tldp.org/HOWTO/Remote-Serial-Console-HOWTO/ For more informations on remote console])		GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the Serial line. With it you can have access to the U-Boot/Linux console of your APF without needing to connect a keyboard/screen to the board. ([http://tldp.org/HOWTO/Remote-Serial-Console-HOWTO/ For more informations on remote console])

	==Installation==		==Installation==

JulienB: /* Configuration */

2009-05-16T09:07:39Z

Configuration

← Older revision		Revision as of 11:07, 16 May 2009
Line 19:		Line 19:
	Port: /dev/ttyS0 Speed:115200 Parity: None		Port: /dev/ttyS0 Speed:115200 Parity: None
	Bits: 8 Stop bit: 1 Flow control: None		Bits: 8 Stop bit: 1 Flow control: None
	* Press OK then in the same menu save the configuration as "armadeus"		* Press OK then in the same menu save the configuration as "armadeus". Next time you will launch GTKTerm don't forget to reload this configuration.

	{{:Serial port selection generalities}}		{{:Serial port selection generalities}}

JulienB: New page: GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the RS232 line. With it you can have access to the U-Boot/Linux console of your A...

2009-05-15T16:01:01Z

New page: GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the RS232 line. With it you can have access to the U-Boot/Linux console of your A...

New page

GTKTerm is a graphical serial line terminal emulator that allows you to take control of your board through the RS232 line. With it you can have access to the U-Boot/Linux console of your APF without needing to connect a keyboard/screen to the board. ([http://tldp.org/HOWTO/Remote-Serial-Console-HOWTO/ For more informations on remote console])

==Installation==
===On *Ubuntu / Debian===
<pre class="host">
$ sudo apt-get install gtkterm
</pre>
or use your graphical package manager.

===On Fedora===
# rpm -q ???

==Configuration==
* Launch it and it will create a default configuration file:
<pre class="host">
$ gtkterm
</pre>
* In the "Configuration" menu select "Ports" and set the parameters to:
Port: /dev/ttyS0 Speed:115200 Parity: None
Bits: 8 Stop bit: 1 Flow control: None
* Press OK then in the same menu save the configuration as "armadeus"

{{:Serial port selection generalities}}