BootStrap - Revision history

FabienM: /* Introduction */

2020-05-06T14:31:18Z

Introduction

← Older revision		Revision as of 16:31, 6 May 2020
Line 21:		Line 21:
	\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]		\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]
	\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (off BOOT0 & on BOOT1)]]
	\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]		\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]
	\|----------------		\|----------------

JulienB: /* Usage */

2018-11-27T14:55:44Z

Usage

← Older revision		Revision as of 16:55, 27 November 2018
Line 57:		Line 57:
	</pre>		</pre>

	\|\|		\|\|<pre class="host">
			APF27 Bootstrap Tool

			/!\ Do not forget to put the bootstrap jumper and to reset your board /!\
			(be sure to have a file named apf27-u-boot-nand.bin in current dir too)

			/!\ U-Boot recover eat lot of CPU, be sure that no process trust your CPU

			Enter serial port number or name to use (/dev/ttySx under Linux and COMx under Windows):
			</pre>
	\|\|		\|\|

Line 119:		Line 127:

	\|\|<pre class="host">		\|\|<pre class="host">
	run flash_uboot		successful operation completion
	device 0 ~~offset 0x0, size 0xa0000~~		SDRAM INIT1 APF SDRAM INIT2 APF
	nand_unlock: start: 00000000, length: ~~655360~~!		Transfering:
			379952 bytes transfered
			Successful download completion


			U-Boot 2012.04.01 (Dec 21 2016 - 17:20:47) apf27 patch 3.8

			I2C: ready
			DRAM: 128 MiB
			NAND: 256 MiB
			*** Warning - bad CRC, using default environment

			In: serial
			Out: serial
			Err: serial
			nand_unlock: start: 000a0000, length: 267780096!
			Net: FEC
			Hit any key to stop autoboot: 0
			BIOS>Would you like to erase the environment variables? y/n: y
			env default -f && saveenv && echo Flash environment variables erased!
			## Resetting to default environment
			Saving Environment to NAND...
			Erasing Nand...
			Erasing at 0xe0000 -- 100% complete.
			Writing to Nand... done
			Flash environment variables erased!
			BIOS> setenv fileaddr A0000000; setenv filesize 0005cc1c;run flash_uboot
			device 0 whole chip
			nand_unlock: start: 00000000, length: 268435456!
	NAND flash successfully unlocked		NAND flash successfully unlocked

	NAND erase: device 0 offset 0x0, size 0xa0000		NAND erase.part: device 0 offset 0x0, size 0xa0000
	OK		OK

	NAND write: device 0 offset 0x0, size ~~0xa0000~~		NAND write: device 0 offset 0x0, size 0x5cc1c
	~~655360~~ bytes written: OK		379932 bytes written: OK
	NAND flash successfully locked		NAND flash successfully locked
	device 0 offset 0xa0000, size ~~0x7f60000~~		device 0 offset 0xa0000, size 0xff60000
	nand_unlock: start: 000a0000, length: ~~133562368~~!		nand_unlock: start: 000a0000, length: 267780096!
	NAND flash successfully unlocked		NAND flash successfully unlocked
	Flashing of uboot succeed		Flashing of uboot succeed
	BIOS>~~uBoot~~ successfully recovered !		BIOS>U-Boot successfully recovered !
	</pre>		</pre>
	\|\|		\|\|

JulienB: /* Introduction */

2018-10-01T14:12:13Z

Introduction

← Older revision		Revision as of 16:12, 1 October 2018
Line 22:		Line 22:
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]
	\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]
	\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6ULDev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]
	\|----------------		\|----------------
	\|}		\|}

JulienB: /* Usage */

2016-11-09T14:08:42Z

Usage

← Older revision		Revision as of 16:08, 9 November 2016
Line 29:		Line 29:
	==Usage==		==Usage==
	* '''Quit all Kermit/Minicom/GTKTerm/Hyperterminal sessions connected to the board through Serial Port.'''		* '''Quit all Kermit/Minicom/GTKTerm/Hyperterminal sessions connected to the board through Serial Port.'''
	*Go inside the ''software/uboot_recover/'' directory and launch (sudo usage is ~~only~~ required on [[APF28]], [[APF51]] and [[~~APF6~~]]):		*Go inside the ''software/uboot_recover/'' directory and launch (sudo usage is required on [[APF28]], [[APF51]], [[APF6]] and [[OPOS6UL]]):
	<pre class="host">		<pre class="host">
	$ cd software/uboot_recover/		$ cd software/uboot_recover/
	$ sudo python ~~apfXX_recover~~.py (XX depends on the version of your board (ie: ~~9328~~, 27, 28, 51 or 6))		$ sudo python xxxx_recover.py (xxxx depends on the version of your board (ie: apf9328, apf27, apf28, apf51, apf6 or opos6ul))
	</pre>		</pre>

JulienB: /* Usage */

2016-09-09T14:13:26Z

Usage

← Older revision		Revision as of 16:13, 9 September 2016
Line 40:		Line 40:
	{\| border="1" cellpadding="5" cellspacing="0" summary="Tool instructions"		{\| border="1" cellpadding="5" cellspacing="0" summary="Tool instructions"
	\|- style="background:#efefef;"		\|- style="background:#efefef;"
	! '''APF9328''' \|\| '''APF27''' \|\| '''APF51''' \|\| '''APF28''' \|\| '''APF6'''		! '''APF9328''' \|\| '''APF27''' \|\| '''APF51''' \|\| '''APF28''' \|\| '''APF6''' \|\| '''OPOS6UL''
	\|----------------		\|----------------
	\|\|		\|\|
Line 78:		Line 78:

	--- Enter serial port number or device name to use for console (/dev/ttyUSB0 under Linux (default) or COMx under Window$):		--- Enter serial port number or device name to use for console (/dev/ttyUSB0 under Linux (default) or COMx under Window$):
			</pre>
			\|\|<pre class="host">
			--- OPOS6UL Bootstrap Tool ---

			Procedure to follow:
			1] Be sure to:
			* have built the OPOS6UL BSP (make opos6ul_defconfig; make),
			* have "sb" tool installed on your PC (on Ubuntu: sudo apt-get install lrzsz),
			* have launched this script as root (sudo).
			2] Power off your board, close all serial terminal sessions, remove all USB cables
			3] Take jumper off BOOT1 pins and put it on BOOT0 pins.
			4] Power on your board
			5] Connect a USB cable from your PC to the OPOS6ULDev OTG miniUSB connector
			6] Connect a USB cable from your PC to the OPOS6ULDev console/debug miniUSB connector

			--- Then, enter serial port number or device name to use for console (/dev/ttyUSB0 under Linux (default) or COMx under Window$):
	</pre>		</pre>
	\|----------------		\|----------------
Line 88:		Line 104:
	{\| border="1" cellpadding="5" cellspacing="0" summary="Recovery final messages"		{\| border="1" cellpadding="5" cellspacing="0" summary="Recovery final messages"
	\|- style="background:#efefef;"		\|- style="background:#efefef;"
	! '''APF9328''' \|\| '''APF27''' \|\| '''APF51''' \|\| '''APF28''' \|\| '''APF6'''		! '''APF9328''' \|\| '''APF27''' \|\| '''APF51''' \|\| '''APF28''' \|\| '''APF6''' \|\| '''OPOS6UL'''
	\|----------------		\|----------------
	\|\|<pre class="host">		\|\|<pre class="host">
Line 237:		Line 253:
	--- Now you can remove miniUSB OTG cable and put the jumper back on BOOT0 pin. Your board is running...		--- Now you can remove miniUSB OTG cable and put the jumper back on BOOT0 pin. Your board is running...
	</pre>		</pre>
			\|\|<pre class="host">
			--- U-Boot successfully recovered !
			--- Now you can remove the miniUSB OTG cable and put the jumper back on BOOT0 pin. Your board will boot... As the restored U-Boot version may differ from the one your were using, if you want to maximize the chances to keep your rootfs data safe, we strongly advise you to reflash the same U-Boot version your were using before the recovery. Otherwise (you don't care about your data), please upgrade to the latest available stable Armadeus U-Boot release.
			</pre>

	\|----------------		\|----------------
	\|}		\|}

JulienB at 13:19, 9 September 2016

2016-09-09T13:19:10Z

← Older revision		Revision as of 15:19, 9 September 2016
Line 10:		Line 10:
	</pre>		</pre>

	This utility communicates with the i.MX(L/27/28/51/6) processor while in ''bootstrap mode'' (See i.MX(L/27/28/51/6) Reference Manual for more informations).		This utility communicates with the i.MX(L/27/28/51/6/6UL) processor while in ''bootstrap mode'' (See i.MX(L/27/28/51/6/6UL) Reference Manual for more informations).

	* To enter the bootstrap mode, you have to put the bootstrap jumper and reset your Armadeus board: <br>		* To enter the bootstrap mode, you have to put the bootstrap jumper and reset your Armadeus board: <br>

JulienB: /* Introduction */

2016-09-09T13:18:33Z

Introduction

← Older revision		Revision as of 15:18, 9 September 2016
Line 22:		Line 22:
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]
	\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]
			\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6ULDev]] (BOOT0 & BOOT1)]]
	\|----------------		\|----------------
	\|}		\|}

JulienB: /* Usage */

2015-04-24T12:04:35Z

Usage

← Older revision		Revision as of 14:04, 24 April 2015
Line 57:		Line 57:

	\|\|		\|\|
	~~The size of the SDRAM has to be indicated. Default value is 64Mo.~~
	~~<pre class="host">~~
	~~TBDL~~

	~~</pre>~~
	\|\|		\|\|

FabienM: /* Introduction */

2015-04-03T13:08:08Z

Introduction

← Older revision		Revision as of 15:08, 3 April 2015
Line 15:		Line 15:
	{\|border=0 summary="Photos"		{\|border=0 summary="Photos"
	\|----------------		\|----------------
	\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]] \|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]] \|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]		\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]]
			\|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]]
			\|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]
			\|----------------
	\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]		\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]

JulienB: /* Introduction */

2014-12-24T11:35:34Z

Introduction

← Older revision		Revision as of 13:35, 24 December 2014
Line 16:		Line 16:
	\|----------------		\|----------------
	\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]] \|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]] \|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]		\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]] \|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]] \|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]
	\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]]]]		\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]
	\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]

← Older revision		Revision as of 16:31, 6 May 2020
Line 21:		Line 21:
	\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]		\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]
	\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (off BOOT0 & on BOOT1)]]
	\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]		\|\| [[Image:bootstrap_jumper_opos6uldev.jpg\|thumb\|right\|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]
	\|----------------		\|----------------

← Older revision		Revision as of 15:08, 3 April 2015
Line 15:		Line 15:
	{\|border=0 summary="Photos"		{\|border=0 summary="Photos"
	\|----------------		\|----------------
	\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]] \|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]] \|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]		\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]]
			\|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]]
			\|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]
			\|----------------
	\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]		\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]

← Older revision		Revision as of 13:35, 24 December 2014
Line 16:		Line 16:
	\|----------------		\|----------------
	\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]] \|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]] \|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]		\| [[Image:bootstrap_jumper.jpg\|thumb\|left\|On the [[APF9328DevLight]]]] \|\| [[Image:bootstrap_jumper_devfull.jpg\|thumb\|center\|On the [[APF9328DevFull]] (Boot)]] \|\| [[Image:bootstrap_jumper_apf27.jpg\|thumb\|right\|On the [[APF27Dev]] (J12)]]
	\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]]]]		\|\| [[Image:bootstrap_jumper_apf51.jpg\|thumb\|right\|On the [[APF51Dev]] (Boot)]]
	\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]		\|\| [[Image:bootstrap_jumper_apf28dev.jpg\|thumb\|right\|On the [[APF28Dev]]]]
	\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]		\|\| [[Image:bootstrap_jumper_apf6dev.jpg\|thumb\|right\|On the [[APF6Dev]] (BOOT0 & BOOT1)]]